🌐 Internet Verified (Unverified by Owner): Controls have been validated using official web MIDI specifications (under CC BY-SA 4.0 via MIDI.guide), but not tested on physical hardware. Help us verify them by adjusting the sliders!

Profile ID: behringer-pro-800

Pro-800

Polyphonypoly

Engine Typepoly

Voice Count8 Voices

Timbral Parts1 Part

The Behringer Pro-800 is an 8-voice polyphonic analog synthesizer based on the classic Sequential Circuits Prophet-600, featuring dual VCOs, noise generator, LFO, and dual envelope generators.

💡 How to configure the Behringer Pro-800 in closeby.one▼

To connect your Behringer Pro-800 to your web browser, connect your synth using a USB cable or a dedicated USB-to-MIDI interface.

Open the MIDI Settings panel above, set the Output Port to your connected Pro-800 device, and select the correct MIDI channel (default is channel 1). Once configured, you can map the MIDI CC layout sliders, draw automated parameter curves, and edit patches in real-time without installing any software.

💡 MIDI Routing Guide: For detailed configuration tips, CC parameters list, and step-by-step setup guides, read the full, dedicated Behringer Pro-800 MIDI Connection Guide.

MIDI CC List & Web Editor

Browse CC parameters, tweak sliders, and automate your synth in real time.

MIDI Hardware Device

Midi Ch

Test Trigger

Actions

Mixer

(1 control)

Master Volume (CC 7)0

Adjusts the master output volume.

Envelopes

(8 controls)

VCF EG Attack (CC 93)0

Adjusts the attack time of the filter envelope.

VCF EG Decay (CC 92)0

Adjusts the decay time of the filter envelope.

VCF EG Sustain (CC 91)0

Adjusts the sustain level of the filter envelope.

VCF EG Release (CC 90)0

Adjusts the release time of the filter envelope.

VCA Attack (CC 101)0

Adjusts the attack time of the amplitude envelope.

VCA Decay (CC 100)0

Adjusts the decay time of the amplitude envelope.

VCA Sustain (CC 95)0

Adjusts the sustain level of the amplitude envelope.

VCA Release (CC 94)0

Adjusts the release time of the amplitude envelope.

LFO

(2 controls)

LFO Freq (CC 104)0

Adjusts the frequency / speed of the Low Frequency Oscillator.

LFO Amount (CC 105)0

Adjusts the global LFO modulation depth.

General / Utility

(11 controls)

Mod Wheel (CC 1)0

Controls the modulation wheel depth.

Osc A Freq (CC 80)0

Adjusts the frequency coarse pitch of Oscillator A.

Osc A Vol (CC 81)0

Controls the output level of Oscillator A.

Osc A PW (CC 82)0

Adjusts the pulse width of Oscillator A.

Osc B Freq (CC 83)0

Adjusts the frequency coarse pitch of Oscillator B.

Osc B Vol (CC 84)0

Controls the output level of Oscillator B.

Osc B PW (CC 85)0

Adjusts the pulse width of Oscillator B.

Osc B Fine (CC 86)0

Fine-tunes the frequency of Oscillator B.

VCF Freq (CC 87)0

Controls the cutoff frequency of the 4-pole lowpass filter.

VCF Reso (CC 88)0

Controls the resonance/feedback of the lowpass filter.

Glide (CC 106)0

Controls the portamento / pitch glide rate.

ℹ️ How MIDI CC Sync Works

MIDI CC is a one-way push protocol. Synthesizers cannot be queried dynamically to read their current parameter values. To synchronize these sliders, select your synthesizer's MIDI Input Port above. When you physically tweak knobs on your synth, the slider positions will instantly update on-screen to match.

No presets found for this synth.

ACADEMY

Recommended lessons.

Browse all lessons →

ArpeggioIntermediate

Suggest Profile Edit

Suggest adjustments to descriptions and MIDI CC parameter mapping.