Profile ID: strymon-nightsky

NightSky

Polyphonymono

Engine Typeeffect

Voice Count1 Voice

Timbral Parts1 Part

Strymon NightSky is a time-warped reverberator and audio processing workstation featuring analog-buffered dry path, pitch shifting, modulation, an onboard 8-step sequencer, and complete MIDI CC and Program Change implementation.

💡 How to configure the Strymon NightSky in closeby.one▼

To connect your Strymon NightSky to your web browser, connect your synth using a USB cable or a dedicated USB-to-MIDI interface.

Open the MIDI Settings panel above, set the Output Port to your connected NightSky device, and select the correct MIDI channel (default is channel 1). Once configured, you can map the MIDI CC layout sliders, draw automated parameter curves, and edit patches in real-time without installing any software.

MIDI CC List & Web Editor

Browse CC parameters, tweak sliders, and automate your synth in real time.

MIDI Hardware Device

Midi Ch

Test Trigger

Actions

Mixer

(3 controls)

Dry Level (CC 12)0

Controls the output level of the unprocessed dry analog signal path.

Voice Shimmer Level (CC 29)0

Adjusts the volume of the Shimmer voice in the mix.

Voice Drive Level (CC 34)0

Adjusts the saturation drive/distortion level.

Filter

(1 control)

Tone Filter Mode (CC 24)0

Selects the EQ filter characteristics (Regen Lowpass, Lowpass, Highpass).

Envelopes

(4 controls)

Decay Length (CC 18)0

Adjusts the decay time/RT60 of the reverb engine.

Decay Texture (CC 19)0

Selects the reverberator type/algorithm (Sparse, Dense, Diffuse).

Decay Size/Pitch (CC 20)0

Controls the physical size/pitch of the virtual reverberating space.

Decay Quantize (CC 21)0

Sets pitch quantization style (Smooth, Half-step, Whole-step, Scales).

General / Utility

(27 controls)

Reverb Mix (CC 11)0

Adjusts the balance of wet reverb signal to dry input signal.

Mod Speed (CC 13)0

Adjusts the rate of modulation applied to the reverb lines.

Mod Target (CC 14)0

Selects the destination of the modulation (Verb, Pitch, Filter).

Mod Depth (CC 15)0

Adjusts the depth or intensity of modulation.

Mod Shape (CC 16)0

Selects the LFO modulation waveform (Triangle, Saw, Ramp, Square, Random).

Pre-Delay (CC 17)0

Sets the delay time before the reverb reflections begin.

Tone Low Cut (CC 22)0

Highpass filter cutoff to roll off sub/low-end frequencies from reverb.

Tone High Cut (CC 23)0

Lowpass filter cutoff to damp high frequencies and soften reverb reflections.

Tone Lowpass Q (CC 25)0

Controls the resonance/Q factor of the Tone filter.

Voice Interval (CC 26)0

Sets the pitch shift interval of the shimmer voice (-1 Octave to +1 Octave).

Voice Scale Select (CC 27)0

Selects the scale quantization constraints for pitch shifting.

Voice Shimmer (CC 28)0

Selects the shimmer effect mode (Off, Fast, Slow, Regen).

Voice Glimmer (CC 30)0

Selects Glimmer mode (Off, High band, Low band, Dynamics).

Voice Glimmer Gain (CC 31)0

Sets the input/output gain boost for Glimmer harmonics.

Voice Drive (CC 33)0

Selects preamp drive saturation style (Off, Pre-reverb, Post-reverb).

Freeze (CC 35)0

Triggers Infinite/Freeze behavior to sustain the reverb buffer.

Morph Trigger (CC 36)0

Initiates morphing from current values to morphed preset states.

Morph Speed (CC 37)0

Sets the transition time/rate for parameter morphing.

Sequencer Mode (CC 41)0

Controls sequencer playback mode (Off, Run, Step-thru).

Seq Step 1 (CC 42)0

Toggles active step state for Step 1.

Seq Step 2 (CC 43)0

Toggles active step state for Step 2.

Seq Step 3 (CC 44)0

Toggles active step state for Step 3.

Seq Step 4 (CC 45)0

Toggles active step state for Step 4.

Seq Step 5 (CC 46)0

Toggles active step state for Step 5.

Seq Step 6 (CC 47)0

Toggles active step state for Step 6.

Seq Step 7 (CC 48)0

Toggles active step state for Step 7.

Seq Step 8 (CC 49)0

Toggles active step state for Step 8.

ℹ️ How MIDI CC Sync Works

MIDI CC is a one-way push protocol. Synthesizers cannot be queried dynamically to read their current parameter values. To synchronize these sliders, select your synthesizer's MIDI Input Port above. When you physically tweak knobs on your synth, the slider positions will instantly update on-screen to match.

No presets found for this synth.

Firmware & Help Reference

Firmware Version Details

Latest Stable:v1.20

Firmware update adds MIDI connectivity stability and USB-C audio/MIDI synchronization improvements.

MIDI Troubleshooting

🚨 Pedal does not respond to MIDI messages

Ensure the MIDI Channel (default 1) matches your track settings. Hold the INFINITE footswitch at power-up and turn the SPEED knob to change the MIDI channel. Make sure the EXP jack is set to MIDI mode by holding INFINITE at power-up and turning the REVERB knob until the INFINITE LED is blue.

🚨 MIDI CC parameter updates are not sent back to sequencer

Hold the INFINITE footswitch at power-up and press PRESET BUTTON 4. The LED should turn Green (Send MIDI CC On). If it is Red, CC output is disabled.

Suggest Profile Edit

Suggest adjustments to descriptions and MIDI CC parameter mapping.